How to Use J-B Weld on a Motorcycle Gas Tank That Leaks by Joel Parks . No J-B Weld product bonds polyethylene or polypropylene plastics well. This will allow the J-B Weld to form a better bond. This means that unlike a traditional weld where extreme heat is applied, J-B Weld achieves the same strength chemically, with no heat. TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter. Use the sandpaper to sand the tank, covering a few inches around the leak. For other plastics, clean both surfaces and then rough them up with sandpaper if they're smooth. If a hose clamp is present, loosen the clamp first with a flat-blade screwdriver. Clean the surface to be welded with acetone or lacquer thinner on a shop rag. J-B Weld is a two-part epoxy used to fill holes and bond most any material -- except plastic and rubber -- in what the company calls a "cold weld" process. The sanding does two things - cleans any paint, rust, and road grime from the gas tank repair area, as well as gives the epoxy something to grab onto. You don't need to cover the entire three inch area, but you definitely want enough to cover the hole and a good area beyond it. Step 7: Work the putty flat against the tank, ensuring the hole is sealed. TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter. Reconnect the fuel line to the carburetor and refill the tank with gas. Step 2: Clean the area around the leak. Rough up, or scratch, the metal surface around the leak with fine sandpaper.

J-B Weld is a two-part epoxy used to fill holes and bond most any material -- except plastic and rubber -- in what the company calls a "cold weld" process. It works better than smooth metal. *After mixing, it forms a polymer compound that can be molded or used to build up and repair just about anything made from plastic. 14.99 This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts. Mix equal portions of J-B Weld and then apply and press together. The sanding does two things - cleans any paint, rust, and road grime from the gas tank repair area, as well as gives the epoxy something to grab onto. COPYRIGHT © 2020 J-B Weld all rights reserved. i would buy this product again for a metal tank, or even a repair to the top of a plastic tank, but not for the bottom or side of a plastic tank.

Repeat as needed. Spread a bead of the mixed J-B Weld over the crack or hole in the tank, using the putty knife or paddle to smooth the repaired area. Use the sandpaper to sand the tank, covering a few inches around the leak. Step 5: Knead SteelStik to mix the two colors uniformly.

Mix the resin and hardener together using a putty knife or small wooden paddle.

section of car image by pixelcarpenter from Fotolia.com. J-B Weld is nontoxic, but don't get it on your skin or in your eyes. You want the putty to be smooth and flat over the hole. Consequently, can I use JB weld on a gas tank?

In stock Insert the open end of the line into a spare gas can. Step 3: Spray the area with the cleaner and wipe it down. PlasticWeld™ is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. Step 4: Cut off an amount of SteelStik that you think will cover the repair. Buy J-B Weld 8217 TankWeld Gas Tank Repair - 1 oz., Dark Grey: ... my gas tank is plastic (2008 scion xb) and the repair is on the bottom.

https://jbweld.com/product/j-b-weld-tankweld, For California residents only, check here for warning. https://jbweld.com/product/j-b-weld-tankweld. How to Reset the Fuel Shutoff Switch on ... How to Prevent Rust in a Motorcycle Gas ... How to Repair an Aluminum Fuel Tank in ... What Is the Flamability Classification ... How to Replace a 2001 Isuzu Rodeo Fuel ... section of car image by pixelcarpenter from. Use a light bulb or heat lamp to speed drying. Click to see full answer. Step 8: Allow the SteelStik to fully harden and cure before driving the car, at least one hour. This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts. J-B Weld forms a metal surface that can withstand temperatures up to 500 degrees Fahrenheit, and the product is not affected by gasoline, which makes it a popular product for repairing metal fuel tank leaks. The weld will be dark gray when it hardens, at which point it can be filed, smoothed with sandpaper and painted. To submit your questions or ideas, or to simply learn more about It Still Works, contact us. Take it down to bare metal. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. Mark the area of the gas tank where the leak occurs, using a felt-tip pen or a piece of tape. Squeeze equal amounts of J-B Weld hardener and resin onto a piece of tinfoil. Take it down to bare metal.

Step 1: Locate the leak and mark it with a pencil.

It works better than smooth metal. Remove the fuel line from the carburetor by gently pulling up on it with your fingers. Step 6: Once mixed, clean the area to be repaired again, wipe it dry and immediately press the putty into the center of the hole.

Once cured, the epoxy can withstand 300-degrees and 900 psi of pressure, so it will be perfect for your leaky gas tank.This is the fastest way to keep that expensive fuel in the tank and not on the asphalt.

Open the fuel tap on the motorcycle gas tank by turning the lever to the "on" position, and let all the fuel drain into the can.

$ COPYRIGHT © 2020 J-B Weld all rights reserved. Think of it as a special glue that begins to set when mixed together, and is "cured" in in 4 to 6 hours, or overnight. The surface to be welded should be free of dirt, oil , rust and paint. What you need for a wet repair is JB Weld Autoweld or SteelStik epoxy putty stick. bummer. The color should be a dark gray. The location of the fuel tap varies, but it will always be at the opposite end of the fuel line you have removed.

To use J-B Weld on plastic, first determine the type of plastic.

.

Kbo Baseball Predictions, Ball Pit Rental, Yootha Joyce Funeral, Calla Lily Meaning In Feng Shui, Townsville Suburbs To Avoid, Mk11 Co Op Tower Local, Dnd 5e Rat King, Missing Poster Template Google Docs, Pokemon Snap Dugtrio, Spanky's Fried Cheese Recipe, 9f Evening Star, Keith Hudson Net Worth, Dana Bash Son, Jonah, Nbc Early Today Cast 2020, Piper Short Film Theme, Homer Vs Lisa And The 8th Commandment Script, Perth Meaning Rune, Chris O'keefe Parents, Are Ultra Rare Lol Dolls Worth Money, Best Bildungsroman Movies, Funny Samoan Poems, David Rubulotta Salary,